Perimeter wire calculator

Set your lawn's size, add its beds, trees and ponds, passages and guide wires, and the calculator draws the wire round your lawn and works out how much you need, how many pegs and connectors, and whether the wire in the box is likely to be enough.

How do you know the lawn’s size?
Length and width
m
m

An odd shape? Use the longest length and the average width, or measure the edge and switch to the perimeter.

Perimeter
m

Walk the edge with a tape, or draw it on a map.

m²
Islands to wire round1 · 8 m
  • Flower bed 8 m

Beds, trees and ponds inside the lawn. Measure round each one.

A strip through to a side or back lawn: the wire runs along both sides.

Guide wires back to the dock
Lawn edges
Fine-tune the assumptions
m
m
m
%
107mof wire, with 10% spare
180pegs
Dock20 m12 m
Boundary wire Guide wire Pegs
  • Outer edge 64 m
  • Round islands 8 m
  • Out to islands and back 6 m
  • Guide wire 19 m
  • Spare 10 m

Plus 3 waterproof connectors for joins and repairs, and 3 for the wire ends at the dock (usually in the box).

Any kit covers it. Wired mowers usually come with 150–400 m of wire.

20 wire, pegs and kits we track

Wire from your mower’s own brand is the safe choice: gauges differ, and some manuals specify it.

12 wire-free mowers rated for your lawn

Rather skip the wire? These map the edge in an app instead, and are rated for at least 288 m² (20% over your 240 m²). Cheapest first.

Pegs every 75 cm on straight runs and 40 cm on curves, with 35% of the outer edge curved and all island wire curved, plus 10% spare. Each guide wire is estimated at 30% of the perimeter. Follow your mower’s manual where it differs. See our installation guide, all wire-free mowers and perimeter wire vs wire-free.

How to use the calculator

  1. Give the lawn's size. For a roughly rectangular lawn, set the length and width. Otherwise choose I know the perimeter and enter the edge length in metres: walk it with a measuring wheel or tape, or measure it on a map with the lawn size calculator. Add the area too if you know it.
  2. Add your islands. Tap Flower bed, Tree or Pond to add a typical one, or type the measurement round any other obstacle the mower should avoid. Tap the cross on an island to remove it.
  3. Count passages. A narrow passage to a side or back lawn needs wire along both sides. Use the plus button for each one. If you measured each lawn area's edge separately, add them all to the perimeter and still count the links between them.
  4. Choose how many guide wires. Many wired mowers use one to find their way back to the charging station. Check the manual; some models don't use one.
  5. Pick the shape of your edges. Curves need more pegs.

The result updates as you go. The plan draws your lawn to scale with the wire round it, out and back to each island and through each passage, the guide wires from the dock, and pegs along the wire. Islands are placed for illustration, at the distance from the edge the calculator assumes; if you only gave a perimeter, the lawn is drawn as a rectangle with that perimeter.

How the wire is worked out

  • Outer edge: the perimeter you entered.
  • Islands: the perimeter of each, plus a run out from the edge and back along the same path. We assume each island is 3 m from the edge; change that under Fine-tune the assumptions.
  • Passages: two runs of wire through each, 5 m long by default. Wired mowers usually need the two runs at least 60 cm apart with a guide wire between them, and wider without one; our installation guide has the figures.
  • Guide wire: if you don't enter a length, each guide wire is estimated at 30% of the perimeter, roughly the run from the charging station to a far part of the lawn.
  • Spare: 10% on top, for slack loops at the charging station and corners, joins, and the odd mistake. A few spare loops near beds you might move later save re-laying wire.

The total is rounded up to a common reel size (50, 100, 150, 200, 250, 300, 400 or 500 m).

Pegs and connectors

Pegs are counted at 75 cm apart on straight runs and 40 cm on curves. Island wire is treated as curved, and a share of the outer edge is too, depending on the edge shape you chose. The two runs out to an island lie side by side and share pegs. We add 10% spare and round up to the next 10.

Connectors cover the joins: one where each guide wire meets the boundary loop, one for each extra reel, and two spare for repairs. Ordinary twisted joins and tape corrode outside, so use the waterproof connectors made for the job. The wire ends at the charging station also need connectors, which usually come with the mower.

Will the wire in the box be enough?

Wired robot mowers typically come with 150 to 400 m of boundary wire, plus pegs and connectors. Smaller models sit at the lower end. The calculator tells you the smallest typical kit that would cover your total, and how much extra wire you'd need if your mower comes with less. Where we track extra wire, pegs or installation kits from the mower brands, they're listed with the result, with how many reels or packs your lawn needs.

Laying the wire

Plan the route on a sketch, set the distance from the edge to suit what's beyond it, peg the wire on the surface and run the mower for a couple of weeks before burying it. Our guide to installing a robot mower covers each step, including passages, guide wires and islands.

Or skip the wire altogether

If the numbers look daunting, a wire-free mower may suit better. RTK, camera and LiDAR mowers are set up by driving the edge with an app instead of laying wire, though they cost more and some need a clear view of the sky. If the calculator knows your lawn's area, it suggests wire-free models rated for it. Read perimeter wire vs wire-free for the trade-offs, and use the mowing time calculator to check how long a model takes on your lawn.

Frequently asked questions

How much boundary wire do I need for a robot mower?

Measure the outer edge of the lawn, add the perimeter of each bed, tree or pond you want the mower to avoid, add twice the distance from the edge to each of those islands, and allow about 10% extra for slack and joins. A 10 m by 8 m lawn with one round bed typically needs around 50 m; a large garden with several beds and a guide wire can need 300 m or more.

How many pegs do I need for robot mower wire?

Allow a peg roughly every 75 cm on straight runs and every 30 to 40 cm on curves and around islands. That works out at about 150 to 200 pegs for 100 m of wire, depending on how curvy the edges are. Some guides suggest a peg every metre on straight runs; closer spacing keeps the wire flat until the grass grows over it.

How much wire comes with a robot mower?

It varies by model. Wired mowers typically come with somewhere between 150 and 400 m, with smaller models at the lower end, along with pegs and connectors. Check the box contents on the manufacturer's page for your model before you buy extra.

Do islands really need wire out and back?

Yes. The wire runs from the outer edge out to the island, round it, and back along the same path. Laid close together, the outgoing and returning runs cancel each other's signal, so the mower drives over them. The two runs mustn't cross.

Can I use any make of boundary wire?

Often, but not always. Wires differ in thickness and insulation, and some manuals specify the wire to use. Your mower's own brand is the safe choice, especially for joins, which need waterproof connectors.

Next steps

Plan the install, or weigh up a wire-free mower instead.